Kimray

*NOTE* THIS IS A REPAIR KIT FOR THE PRODUCT SHOWN AND LISTED 

KIMRAY (#RAA) 212 SGT-BP Gas Back Presure Regulator Repair Kit

Vent lines on oil and gas separators, heater treaters, compressor stations and gas gathering systems. 

QUICK SPECS:

-2" Size 
-Fluid: Gas
-Temp Range: -20º to 450ºF
-Elastomers: Buna N, HNBR, FFKM, Polyurethane, Polyacaylate, GLYON®
-Control Range: Up to 280 psig
-5-125 Operating Pressure
-175 Max Working Pressure  

More information available from KIMRAY through the links below:

AAA Catalog Page
Instruction Manual
Repair Manual

KIMRAY (#ABC2) AT ADA Double Acting MOTOR VALVE 212 SMT ADA

Features 

- 300 Max Working Pressure
- RHE Repair Kit 

Liquid metering vessels where up to 250 psig adjustable back pressure is desired. Burner valve for throttling or snap-action service. Any system that requires a double-acting motor valve but also requires an adjustable maximum back pressure.

More information available from KIMRAY through the links below:

ABC2 Catalog Page
Instruction Manual
Repair Manual

KIMRAY (#HCH) ¾" x 12" Seperable Socket Thermowell 

Increases working pressure of Thermostat Sensing Element. All Separable Sockets are filled with high temperature grease. Allows thermostat removal without losing vessel pressure. One piece construction.

 QUICK SPECS:

- Male Thread Size NPT: ¾”
- Material: Steel, 316SS6
- Structural Design Rating: 4000 psi

More information available from KIMRAY through the links below:

HCH Catalog Page

KIMRAY (#EMC) 2" Threaded Low Pressure 212 SMT Motor Valve 

Features

- 175 Max Working Pressure
- RCN Repair Kit 

Pilot-operated oil or water dump valve for separators, emulsion treaters and other similar liquid accumulators. Any system requiring a valve to close when it receives a pneumatic signal. These valves are available at extra cost with a spring under the diaphragm plate that will hold the valve full open whenever pressure on top of the diaphragm is released. This assembly is for applications where small differential pressures exist and capacities required are greater than those shown on the MT capacity chart in this section. To order this assembly, specify the valve number and add “with spring under diaphragm.” For capacities of valves so equipped, refer to MT-DA capacity chart in this section.

More information available from KIMRAY through the links below:

EMC Catalog Page
Instruction Manual
Repair Manual

*NOTE* THIS IS A REPAIR KIT FOR THE PRODUCT SHOWN AND LISTED 

KIMRAY (RFP-V) VITON REPAIR KIT FOR 2" BALANCED MOTOR VALVE 250 SMT PB PO-D

Pilot-operated oil or water valve for separators, meters and water knockoutswhere a reduced signal pressure is available.

More information available from KIMRAY through the links below:

RFP-V Catalog Page
Instruction Manual
Repair Manual

KIMRAY (#YDM) 30 PR Sense Line Protector 

As an adjustable, self-resetting, pressure-limiting device to protect instrumentation from over pressurization and subsequent damage. Designed to protect pilots on high-pressure regulators. Blocks the sense line or supply pressure to a device when it exceeds the adjustable limit of 300 psig. Reopens when inlet pressure drops below the limit.

QUICK SPECS:

- Control: Snap
- Material: Steel, 316SS
- Connections: ¼” NPT
- Structural Design Rating: 1000 psi
- Output Pressure: 0-300 psi
- Repair Kit: RMV 

More information available from KIMRAY through the links below:

YDM Catalog Page
Learn More

KIMRAY (#EFG) 2150 Piston Balanced Motor Valve 

Features 

- 1500 Max Working Pressure 
- RUR Repair Kit 

This Piston Balanced Control Valve (aka: Motor Valve) an be used for discharge of liquid or gas from vessels, separators, heater treaters, knockoutsand other similar liquid accumulators. For back pressure or pressure reducingapplications with pressure pilots.

More information available from KIMRAY through the links below:

EFG Catalog Page
Instruction Manual
Repair Manual